EMT Practice Test

1. Question Content...

---

Question1: Which two interface types are used as tunnel endpoints? (Choose two.)

Question2: You want to see a detailed list of all established BGP sessions. In this scenario, what would be a valid command to accomplish this task?

Question3: Which two statements are correct about the behavior of IS-IS metrics? (Choose two.)

Question4: You are deploying link aggregation groups.

Question5: Exhibit

Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

Question6: Exhibit

Referring to the exhibit, which two statements are correct? (Choose two.)

Question7: Which new field is added to an IPv6 header as compared to IPv4?

Question8: You are troubleshooting two OSPF routers that have an adjacency that remains in the ExStart state.
What would cause this problem?

Question9: You want to share routes between two routing instances that you have configured?
What are two ways to accomplish this task? (Choose two.)

Question10: Exhibit

Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)

Question11: Exhibit

Referring to the exhibit, which two statements are correct? (Choose two.)

Question12: Click the Exhibit button.

All devices in the network are configured correctly and the path requirements are valid.
Referring to the exhibit, which two statements are correct? (Choose two.)

Question13: Exhibit

Referring to the exhibit, which two statements are correct? (Choose two.)

Question14: Which BGP message type is used to re-advertise routes that have already been sent to a peer and acknowledged using TCP?

Question15: By default, which two statements are correct about switch ports on a Junos device? (Choose two.)

Question16: Which BGP attribute Is used to detect touting loops?

Question17: You are implementing traffic engineering in your MPLS network. You must ensure that the MPLS routes are used to traverse your network. Your solution should not affect IGP routes in your route tables.
In this scenario, which traffic engineering setting will accomplish this behavior?

Question18: Exhibit
S Exhibit
LSI1 A AS 65501
ISPB AS 65502
Advertised Prefixes: 172.20.0.0/24 172.20.20.0/24 172.20.21.0/24
\ N
Advertised Prefixes: 172.20.0.0/24
172.20.1.0/24

Referring to the exhibit, which two statements are correct? (Choose two.)

Question19: Which two steps are required to enable MPLS on a physical interface in Junos? (Choose two.)

Question20: Exhibit

Referring to the exhibit, which statement is true about VRRP?

Question21: You have created a routing instance named vr3 that will provide access to Server 2 (10.0.0.2) (or the hosts on the 10.10.10.0/24 network. Which command would you use to test connectivity between vr3 and Server 2?

Question22: Which statement is correct about IS-IS?

Question23: Exhibit

Referring to the exhibit, how do you verify the status of the tunnel from R1?

Question24: Exhibit

You are asked to configure the OSPF environment to prevent the DRother routers from participating in DR/BDR election.
Referring to the exhibit, which command will accomplish this task?

Question25: Exhibit

The LSP is not establishing correctly.
Referring to the exhibit, what should you do to solve the problem?

Question26: What are three well-known mandatory BGP attributes? (Choose three.)

Question27: Exhibit

Routers R1 and R4 have a VRRP priority of 90, while R2 and R3 have default VRRP priorities Referring to the exhibit, which router will be elected as the primary VRRP router?

Question28: Exhibit

Which two statements ate correct about the actions taken as the packet traverses the service provider MPLS network from Site 1 to Site 2 as shown in the exhibit? (Choose two.)

Question29: Which configuration selling prohibits a static route from being redistributed by a dynamic routing protocol?

Question30: Which two statements are correct when using LDP? (Choose two.)

Question31: Exhibit

Referring to the exhibit, which two additional steps should you lake to fully configure NSR? (Choose two.)

Question32: Exhibit

You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.
Which two tasks will accomplish your objective? (Choose two.)

Question33: Exhibit

Which type of load balancing is shown in the exhibit?

Question34: What is the correct order of BGP attributes for active route selection?

Question35: Exhibit

Referring to the exhibit, what will happen to untagged frames?

Question36: Which statement is correct about the FE80;:/10 prefix?

Question37: Exhibit

You have an established LSP between your R1 and R5 devices using the configuration shown in the exhibit. You are asked to ensure that MPLS labels are used to forward traffic by all devices within the LSP.
Which action will accomplish this behavior?

Question38: Click the Exhibit button.

Referring to the exhibit, from which device(s) does R3 learn about Route X?

Question39: Which two LSA types are permuted in OSPF totally stubby areas? (Choose two.)

Question40: Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?

Question41: You are adding an IPv6 configuration to an Interface on a Junos device.
In this scenario, which statement is correct?